www.rumpelbumpel.de   Gameserver Mapping and more  Counterstrike Source   home of the afterSource Project  
Main
RumpelBumpel Clan
CS:aftersource
Online
offline0 User

offlinechengjiayim
offlinelucyweiweiwei
offlinemisshuana
offlinecaicai2017
offlinegustvelope

online3 Gäste

Gesamt: 452242
Heute: 51
Gestern: 135
Gbook einträge: 169
Forum Posts: 12260
Forum Threads: 4485
Registrierte User: 656
Online: 8
... mehr
Geburtstag
qLgaming hat am 02.12.2017 Geburtstag
 
Zander hat am 03.12.2017 Geburtstag
 
NoHero4N hat am 03.12.2017 Geburtstag
Technik-Tutorials
Umfrage und Ergebnisse
FunBox
Shoutbox
Bitte erst Einloggen


Load
ARCHIV
» Canada Goose Pa...
von chengjiayim
» David Wheeler J...
von lucyweiweiwei
» body building a...
von misshuana
» as is possible ...
von misshuana
» use too many be...
von misshuana

» Alle afterSource Maps

» CS:S-Conquest

» HL2EP2.ttf buttons_32.vbf

» de_rumpel_dust2

» aequitas
» neue Server ip´s
» Trialzeit bestanden und ein Trialmember
» Neue Trialmember für ESL
» Trialzeit bestanden
» afterSource Homepage online


    Regist
» Forum » Mapping & Modeling » CS: afterSource » Anregungen und Wünsche » Using your fingers to straighten a warpe

Using your fingers to straighten a warpe
containerhouse

Private Nachricht an den User senden E-Mail an den User senden Hompage des Users besuchen User in ICQ Liste hinzufuegen


Einmalposter
Posts:
Posts: 5


Dabei seit: 24. Mar 2016


# 24.03.2016 - 08:11:06
    zitieren



This is something I’ve never seen an any Ceramic China Brake Factory before.

If you get any on the brake pads, it’s best to replace them.

You might be able to save them by sanding off the top layer of pad material, but often the oil or fluid with seep into the material and then continually contaminate the rotor, which will impact braking.

Squeezing the brake lever with the wheel off the bike.

If you do this with hydraulic brakes without a pad separator between the pads, they’ll push in until they contact each other and then won’t retract enough to get the rotor back in place.

Fortunately, the fix is easy: Wiggling the pad separator in place can re-set the pads.

If the brake is hydraulic, squeeze the brake lever several times to seat and adjust the pads.

If your brake is mechanical, adjust pads according to the manufacturer's instructions. Double-check to ensure the rotor is not rubbing or dragging on the pads.

If the rotor drags, adjust the caliper to eliminate friction. Ride your bike, activating the brakes in quick, hard pulses to season the pads.

Use caution on your first ride, as brand-new pads take a number of stops to reach full power.

Forgetting to check brake pad thickness. Disc brakes are low maintenance, but the pads do wear out.

If the separator doesn’t fit, remove the pads and use something thin and flat (like a flathead screwdriver) to carefully push the pistons back into the body of the brake.

Reinstall the pads and the wheel, squeeze the brake lever a few times, and you’re good to go.

Using the wrong tools or fluid. Using mineral oil in a brake meant for DOT brake fluid (or vice versa) is a recipe for failure. So is not using a torque wrench to tighten fasteners.

And using your fingers to straighten a warped rotor? Well, we already covered that.

So, your rules of thumb: If you plan on maintaining your brakes yourself, know which type of brake fluid to use; always use a torque wrench; and use a tool—not your fingers—to true a rotor.

If your brake levers bottom out against the AT Brake, you need more cable tension.
offline

 

 

CS:GO
Ballerbude Dawn-Server.de
de_dust2
Spieler: 0 / 12


 
Server Fun und War
EU/Royal ARK PVP/15x ALL/Mods/Active Admins - (v268.255)
TheIsland
Spieler: 0 / 40
RumpelBumpel Server
Suche



erweiterte Suche

Links
Counterstrike afterSource
Play with skill
www.ilch.de
Electronic Sports League
Teamspeak
SourceMod Admin Plugin
Steambans
Notepad++